Panel thickness is the specification that quietly decides three things at once: how hard your refrigeration unit has to work, how much cargo volume and payload you keep, and whether the box still holds temperature in August traffic. Choose too thin and the unit runs forever; choose too thick and you have paid for insulation you do not need while giving up cargo space. This guide maps temperature class to thickness using published industry guidance, then covers the three factors that should push you one step thicker — and the reason the assembled body never quite matches the datasheet.
What Panel Thickness Actually Buys You
Thermal resistance vs payload: the real trade-off
Thicker panels raise thermal resistance, which cuts the heat leaking into the box, which lets the refrigeration unit run less and burn less fuel or energy. The cost is geometry: every millimeter of wall thickness comes out of internal cargo width on both sides of the body, and the panel mass itself eats payload. Thickness selection is therefore not 'more is better' — it is matching the insulation to the temperature difference you actually have to hold, on the routes you actually run.
Why the assembled body performs worse than the flat panel
A flat sandwich panel in a test rig is not a truck body. Corners, door frames, floor rails and fasteners create thermal bridges, and one industry technical analysis puts the assembled body's heat-leak performance at 15–25% worse than the flat-panel calculation. The practical consequence: size your thickness with margin, and treat build quality — joints, seals, door fit — as part of the insulation system, because it is.
Thickness by Temperature Class
Manufacturer guidance for refrigerated truck bodies converges on three working classes. These are indicative industry mappings, not UFON stock sizes — UFON builds panels to order up to 100 mm — but they are the right starting point for a specification conversation.
Chilled (0 °C to +8 °C): the 50 mm class
Fresh produce, dairy and beverages moving at chilled setpoints in temperate climates are typically served by panels in the 50 mm class. The temperature difference across the wall is modest, and the dominant heat loads are door openings and solar gain rather than steady-state conduction.
Frozen (around -18 to -20 °C): the 75–100 mm class
Frozen distribution — meat, seafood, ice cream on regional routes — is where published guidance places the 75 mm class as the workhorse, with many fleets stepping to 100 mm for hot climates, long routes or demanding customers. This is the class where the refrigeration unit and the panel specification must be sized together, because neither can fully compensate for the other.
Deep-frozen (-25 °C and below): the 100 mm class
Long-haul deep-frozen, ice cream and pharmaceutical duty call for the 100 mm class. Fixed cold storage practice goes thicker still for deep freezing, but a truck body trades insulation against payload and volume on every millimeter — which is why 100 mm is the practical ceiling for most road applications, and why build quality and thermal-bridge control matter so much at this end of the range.
| Dimension | Chilled (0 to +8 °C) | Frozen (-18 to -20 °C) | Deep-frozen (-25 °C) |
|---|---|---|---|
| Indicative thickness class | ~50 mm class | 75–100 mm class | 100 mm class |
| Typical cargo | Fresh produce, dairy, beverages | Frozen meat, seafood | Ice cream, pharma, long-haul deep-frozen |
| Payload and volume impact | Lowest | Moderate | Highest |
| Refrigeration demand | Standard unit | Larger unit, matched to the box | High-capacity unit mandatory |
| Hot-climate correction (40–45 °C markets) | Consider stepping up | Step up one class | Step up and audit door discipline |

Three Factors That Push You One Step Thicker
Ambient climate (25 °C vs 45 °C markets)
Published manufacturer guidance is explicit on this point: in markets where ambient temperatures run to 40–45 °C, step one thickness class up. The heat flow through the wall scales with the temperature difference across it, and a box specified for a European spring will not hold -20 °C through a Gulf summer without help from thicker walls or a larger unit — usually both.
Door-open frequency (multi-drop vs long-haul)
Every door opening dumps cold air and pulls in hot, humid replacement air that the unit must then re-cool and dehumidify. A multi-drop city route with thirty stops a day behaves like a warmer temperature class than the thermostat suggests. If your operation is multi-drop, treat that as a reason to step up a class — or to look at multi-temperature partitions and tighter door discipline — rather than a reason to oversize only the refrigeration unit.
Refrigeration unit sizing — panel and unit are one decision
A thicker box lets a smaller unit hold temperature; a thinner box forces a larger unit to run continuously, paying for the saved panel thickness in fuel and wear forever. For regulated frozen transport, industry technical references note that ATP FRC-class service at -20 °C requires a whole-body heat-leak coefficient of K ≤ 0.40 W/m²K — a whole-body figure, not a panel figure. Ask every supplier for whole-body performance, and size the unit against the body you are actually buying.
Not All Panels Are Equal: Roof, Walls, Floor and Doors
Why floors and roofs often run thicker
Industry practice has long thickened the roof and floor relative to the walls — one older industry example pairs 85 mm walls with 105 mm roof and floor. The physics supports it: the roof takes direct solar load all day, and the floor faces road-surface heat plus conduction through the sub-frame. The floor is also a structural and airflow component — in UFON bodies it carries the T-shape return-air ducts — so its thickness sets both insulation and air-path geometry.
Doors must match wall thickness
The rear doors are the largest moving seam on the body and the most abused component. Insulated doors should match the wall thickness class, with seals, hinges and lock hardware specified to the same standard — a 100 mm wall paired with a thin, poorly sealed door is a thermal mismatch that shows up directly on the unit's running hours.
The Calculation in Brief: U = λ / d (and the 15–25% Assembly Correction)
Steady-state heat flow through a flat sandwich panel approximates to U = λ / d: thermal conductivity divided by thickness. Using indicative industry figures — PU at λ ≈ 0.022 W/m·K — a 50 mm wall gives a flat-panel U of roughly 0.44 W/m²K, while 100 mm halves that to roughly 0.22. Then apply the reality correction: industry analysis puts assembled-body performance 15–25% worse than the flat-panel number once corners, frames and fasteners are counted. This simple arithmetic explains why the industry converged on its three thickness classes — each step roughly halves the distance the remaining heat has to travel per degree of temperature difference.

UFON Thickness Options and Temperature Ratings
UFON builds insulated panels to order, up to 100 mm thick, with PU, XPS, PET or PP-honeycomb cores and FRP/GRP gelcoat, aluminum, 304 stainless or galvanized skins. Our published temperature classes cover 0 °C chilled, -20 °C frozen and -25 °C deep-frozen duty. Because bodies are engineered to the chassis and cargo rather than pulled from stock sizes, thickness, core and refrigeration unit are matched to your route, climate and door-opening pattern as one specification. Send us the duty cycle — cargo, setpoint, climate, stops per day — and our engineers will come back with a thickness recommendation and the reasoning behind it.
FAQ
What panel thickness do I need for a -20 °C freezer truck?
Published industry guidance places -18 to -20 °C frozen duty in the 75–100 mm class: 75 mm as the workhorse, 100 mm for hot climates, long routes or high door-opening frequency. Remember that the assembled body performs 15–25% worse than the flat-panel figure, so specify with margin and size the refrigeration unit together with the box.
Is 50 mm insulation enough for a chiller truck?
For chilled duty at 0 to +8 °C in temperate climates, the 50 mm class is the standard industry answer. In hot-climate markets at 40–45 °C ambient, manufacturer guidance says to step one class up. Door-opening frequency matters as much as the map: a multi-drop route behaves like a warmer duty class.
Does thicker panel always mean better?
No. Thicker walls cost payload and internal volume, and past the point where conduction is under control, door openings and thermal bridges dominate the heat load anyway. The goal is the thinnest wall that holds your setpoint in your worst-week conditions with the unit sized to match — not the thickest wall you can buy.
Why do freezer truck floors and roofs use thicker panels?
The roof carries direct solar load all day, and the floor faces road-surface heat plus conduction through the sub-frame — industry examples have long paired thicker roof and floor sections with thinner walls. The floor also does structural and airflow work: in UFON bodies it forms the T-shape return-air duct path, so floor thickness sets the air-path geometry too.
How does ambient temperature change the thickness choice?
Heat flow through the wall scales with the temperature difference across it, so a 45 °C ambient roughly doubles the driving force versus a mild climate at the same setpoint. Published manufacturer guidance for 40–45 °C markets is to step one thickness class up — and to re-check refrigeration unit sizing at the same time.
Sources & scope
These sources were reopened and checked on 2026-11-12. Third-party figures are industry references, not UFON test results; project decisions require confirmed drawings, datasheets and destination-specific requirements.
- Zhejiang Miao Sheng Automobile — 50, 75 or 100 mm panelsIndustry starting-point thickness ranges, hot-climate and payload trade-offs; not UFON standard thickness tiers. Accessed 2026-11-12.
- Rax Panel — Cold-storage wall-panel thicknessThermal-resistance formula and cold-storage examples; mobile-body performance needs separate validation. Accessed 2026-11-12.
- HOTECH Engineering Team — Whole-body insulation and thermal bridgesIndicative 15–25% assembled-body penalty and third-party ATP FRC discussion; not official ATP text or a UFON test result. Accessed 2026-11-12.
